Modul CS

Advantages at a glance

  • Stabilising leg or liquid and bulk tippers (rear) 
  • Support while unloading
  • Levelling due to two seperate landing gears
  • Low maitenance because of integrated lubricant cartridge
  • High degree of installation variability thanks to double bolt hole pattern
  • Additional spindle nut
    - Additional protection against wear and tear
    - Minimal risk of accidents

Technical Features

  • Protected against wear by fully sealed gearbox and reinforced inner tube
  • Continuous back plate for high variability during installation
  • Reinforcement for maximum bending strength
  • Heavy duty shaft for better shock resistance
  • Secure stand due to reinforced rigid foot

Technical Specification

 

* Bracing lugs are supplied loose


Note: 

Dimensions A, B and C, see general information.

Selection table / Versions available

Order No. M (mm) H (mm) P (mm) Back plate Foot
CS 1044700R 750 470 728 full length T rigid
CS 1054700R 700 380 678 full length T rigid
CS 1064700R 650 380 628 full length T rigid
CS 1084700R 600 330 578 full length T rigid
CS 1094700R 550 280 528 full length T rigid

Technical Data (per piece / set)

Characteristic Value
Lifting capacity 12 t/ 24 t
Static load 33 t / 66 t
Lift per turn of handle  
- Low gear 0,9 mm
- High gear 15,0 mm
Crank force at 8 t lifting capacity 110 N

Remarks

Please order crank handle separately, see general information.

Two stabiliser legs are required per trailer.

There is no cross shaft.

Modul CS

Item Description Remark Order No. per set
1 Cover JS E0046300 1
2 Bevel gear with bolts JS E0058600 1
3 Cover compl. with bearing compl. JS E0083900 1
3 Cover with bearing compl. from series 0072322 KW 10/2006 JS E0083901 1
4 Grease nipple with protective cap JS E0084000 1
5 Shaft with bearing JS E0084100 1
6 Grease tank JS E0002000 1
7 Gear JS E0055800 1
8 Crank shaft compl. JS E0046500 1
9 Bearing holder compl. JS E0058800 1
10 Crank shaft and bearing holder compl. with 08 + 09 JS E0056600 1
11 Drive compl. compl. with 05, 07 + 10 JS E0084300 1
12 Bolts, washers, nuts JS E0043100 1
13 Crank 350 mm w. parking hook with 12, 14 + 15 JS U01 1
13 Crank 415 mm w. parking hook with 12, 14 + 15 JS U02 1
13 Crank 450 mm w. parking hook with 12, 14 + 15 JS U03 1
13 Crank 480 mm w. parking hook with 12, 14 + 15 JS U04 1
13 Crank 520 mm w. parking hook with 12, 14 + 15 JS U05 1
13 Crank 570 mm w. parking hook with 12, 14 + 15 JS U07 1
13 Crank 620 mm w. parking hook with 12, 14 + 15 JS U08 1
14 Crank bushing JS E0042700 1
15 Crank parking hook for crank 350mm (JS U01) JS E0040200 1
15 Crank parking hook for crank 415-480mm (JS U02 - JS U04) JS E0040201 1
15 Crank parking hook for crank 520mm (JS U05 - JS U08) JS E0040202 1
16 Mh-04/750 shaft right JS E0068303 1
16 Mh-05/700 shaft right JS E0068302 1
16 Mh-06/650 shaft right JS E0068301 1
16 Mh-08/600 shaft right JS E0068304 1
16 Mh-09/550 shaft right JS E0068305 1
17 Axial bearing JS E0066400 1
18 Mh-06/650 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067001 1
18 Mh-05/700 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067002 1
18 Mh-04/750 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067003 1
18 Mh-08/600 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067004 1
18 Mh-09/550 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067005 1
19 Angle JS E010.001 1

Modul CS

Modul CS

PDF-Downloads


Mounting and Operating Instructions
Modul Landing gear 06/2010
Modul CS 06/2010
 
Flyer
MODUL CS Stabilizer leg 09/2016